PRODUCT

AC Motor

□60mm 6W

기본사양

1Ph. Motor
CONTINUOUS DUTY

제품목록

■ PERFORMANCE DATA (DUTY : CONTINUOUS)

Motor Type Output
(W)
Voltage
(V)
Freq.
(Hz)
Rating Starting Condenser
Input
(W)
Current
(A)
Torque
(kgf·cm)
Speed
(rpm)
Torque
(kgf·cm)
(V) (㎌)
IH6PF6-10 6 1ø100 50 25 0.25 0.47 1250 0.40 250 2.5
60 25 0.25 0.38 1550 0.40
IH6PF6-10 1ø100 60 30 0.25 0.38 1550 0.50 250 2.5
IH6PF6-20 6 1ø200 50 25 0.12 0.47 1250 0.40 450 0.7
60 25 0.12 0.38 1550 0.50
IH6PF6-22 1ø220 60 30 0.12 0.38 1550 0.50 450 0.7
IH6PF6-1U 6 1ø115 60 30 0.23 0.39 1500 0.50 250 2.5
IH6PF6-2C 6 1ø220 50 30 0.13 0.47 1250 0.50 450 0.6
7 1ø240 50 35 0.13 0.55 1250 0.55
  • Motor Type은 감속기 직결용인 피니언축으로 표시하였습니다.
    STRAIGHT축의 모터를 희망하시면 Motor Type의 PF를 S로 바꾸어 주문하십시오. 
  • 그린상자표시한 모터는 UL 또는 CE규격을 적용한 TP(Thermal Protect) Type입니다.
  • For motor with straight shaft. please write S in place of PF in Motor Type.
  • Motor Type in green screen represents the motors with TP(Thermal Protect) according to  UL or CE regulation.

■ RATED TORQUE OF GEARED MOTOR

(unit : kg·cm)

Speed of Geared Motor rpm 500 300 200 120 100 60 50 30 20 15 10
Speed of Geared Motor 50Hz 3.5 5 7.5 12.5 15 25 30 50 75 100 150
60Hz 3.6 6 9 15 18 30 36 60 90 120 180
IH6PF6 + 6H□FM 1.1 1.9 2.6 4.7 5.7 8.5 10.2 1.5 23 25 25
IH6PF6 6H□FB 1.1 1.8 2.7 4.6 5.5 8.2 9.9 15 22 25 25
  • 그린상자표시한 감속비의 감속기는 출력축의 회전방향이 모터축의 회전방향과 반대로 됩니다.
  • 감속모터의 회전수(Speed of Geared Motor)는 모터의 회전수 (50Hz에서 1500rpm, 60Hz에서 1800rpm)를 기준하여 산출하였습니다.
    실사용시의 회전수는 부하의 크기에 따라 위의 표보다 2~15% 작게 됩니다.
  • 하얀상자부에는 감속비를 지정하여 주십시오. 감속기는 별도로 판매 됩니다.
  •  The rotation of geared motor in green screen is reverse of motor rotation. · 
  •  Speed of Geared Motor is based on motor synchronous speed. In normal operation, the speed will be 2 to 15 percent lower than above figure. 
  •  When ordering gear head, please fill blank □ with gear ratio.

■ MOTOR(STRAIGHT SHAFT) IH6S6  WT 1.0kg

■ GEARED MOTOR  IH6PF6 + 6H□ FM(6H□ FB)  WT 1.0+0.4kg

■ BOLT SIZE

No L(mm) GEAR RATIO BOLT SIZE
01 30 1/3 ~ 1/18 M4×60
02 40 1/20 ~ 1/200 M4×70

■ KEY SPEC

  • NONE

■ WIRING DIAGRAM

  • 모터의 회전방향은 샤프트 끝쪽에서 볼때의 회전방향입니다.
  • 모터의 회전방향 전환은 모터가 완전히 정지한 후 실시하여 주십시오.
  • The direction of rotation is seen from the end of motor shaft.
  • Change the rotation direction of the motor only after the motor stops completely.