PRODUCT

AC Motor

□70mm 15W

기본사양

1Ph. Motor
CONTINUOUS DUTY

제품목록

■ PERFORMANCE DATA (DUTY : CONTINUOUS)

Motor Type Output
(W)
Voltage
(V)
Freq.
(Hz)
Rating Starting Condenser
Input
(W)
Current
(A)
Torque
(kgf·cm)
Speed
(rpm)
Torque
(kgf·cm)
(V) (㎌)
IH7PF15-10 15 1ø100 50 35 0.40 1.17 1250 0.80 250 5.0
60 35 0.40 0.94 1550 0.80
IH7PF15-11 1ø110 60 45 0.40 0.94 1550 0.90 250 5.0
IH7PF15-20 15 1ø200 50 40 0.20 1.17 1250 0.80 450 1.2
60 40 0.20 0.94 1550 0.80
IH7PF15-22 1ø220 60 45 0.20 0.94 1550 0.90 450 1.2
IH7PF15-1U 15 1ø115 60 45 0.45 0.94 1550 0.90 250 4.0
IH7PF15-2C 13 1ø220 50 45 0.21 1.05 1200 0.80 450 1.0
15 1ø240 50 50 0.21 1.22 1200 0.90
  • Motor Type은 감속기 직결용인 피니언축으로 표시하였습니다.
    STRAIGHT축의 모터를 희망하시면 Motor Type의 PF를 S로 바꾸어 주문하십시오.
  • 그린상자표시한 모터는 UL 또는 CE규격을 적용한 TP(Thermal Protect) Type입니다
  •  For motor with straight shaft, please write S in place of PF in Motor Type. 
  •  Motor Type in green screen represents the motors with TP(Thermal Protect) according to 
  •  UL or CE regulation

■ RATED TORQUE OF GEARED MOTOR

(unit : kg·cm)

Speed of Geared Motor rpm 500 300 200 120 100 60 50 30 20 15 10
Gear Ratio 50Hz 3 5 7.5 12.5 15 25 30 50 75 100 150
60Hz 3.6 6 9 15 18 30 36 60 90 120 180
IH7PF15 + 7H□FM 2.8 4.7 7.1 12 14 21 26 38 50 50 50
IH7PF15 + 7H□FB 2.7 4.6 6.9 11 14 21 25 37 50 50 50
  • 그린상자표시한 감속비의 감속기는 출력축의 회전방향이 모터축의 회전방향과 반대로 됩니다.
  • 감속모터의 회전수(Speed of Geared Motor)는 모터의 회전수 (50Hz에서 1500rpm, 60Hz에서 1800rpm)를 기준하여 산출하였습니다.
    실사용시의 회전수는 부하의 크기에 따라 위의 표보다 2~15% 작게 됩니다.
  • 하얀상자부에는 감속비를 지정하여 주십시오. 감속기는 별도로 판매 됩니다.
  •  The rotation of geared motor in green screen is reverse of motor rotation. · 
  •  Speed of Geared Motor is based on motor synchronous speed. In normal operation, the speed will
  •  be 2 to 15 percent lower than above figure. 
  •  When ordering gear head, please fill blank □ with gear ratio

■ MOTOR(STRAIGHT SHAFT)IH7S15WT 1.2kg

■ GEARED MOTORIH7PF15 + 7H□ FM(7H□ FB)WT 1.2+0.5/0.6kg

■ BOLT SIZE

No L(mm) GEAR RATIO BOLT SIZE
01 31 1/3 ~ 1/18 M5×60
02 41 1/20 ~ 1/200 M5×70

■ KEY SPEC

■ WIRING DIAGRAM

  • 모터의 회전방향은 샤프트 끝쪽에서 볼때의 회전방향입니다.
  • 모터의 회전방향 전환은 모터가 완전히 정지한 후 실시하여 주십시오.
  • The direction of rotation is seen from the end of motor shaft.
  • Change the rotation direction of the motor only after the motor stops completely.