PRODUCT

AC Motor

□80mm 25W(3Ph.)

기본사양

OFF BRAKE TYPE
CONTINUOUS DUTY

제품목록

■ PERFORMANCE DATA (DUTY : CONTINUOUS)

Motor Type Output
(W)
Voltage
(V)
Freq.
(Hz)
Rating Starting Brake Condenser
Current
(A)
Torque
(kgf·cm)
Speed
(rpm)
Torque
(kgf·cm)
Input
(W)
Torque
(kgf·cm)
(V) (㎌)
IHK8PF25-32 25 3ø220 50 0.30 1.87 1300 6.00 6 2.0
60 0.30 1.52 1600 5.00
IHK8PF25-33 25 3ø380 50 0.17 1.87 1300 6.00 6 2.0
60 0.17 1.52 1600 5.00
IHK8PF25-34 25 3ø440 50 0.15 1.87 1300 6.00 6 2.0
60 0.15 1.52 1600 5.00
  • Motor Type은 감속기 직결용인 피니언축으로 표시하였습니다.
    STRAIGHT축의 모터를 희망하시면 Motor Type의 PF를 S로 바꾸어 주문하십시오.
  • 그린상자표시한 모터는 UL 또는 CE규격을 적용한 TP(Thermal Protect) Type입니다
  • 정지하지 않은 상태에서 바로 반대방향으로 회전을 하게 되면 MOTOR에 무리한 관성이 가해져 파손 및 수명이 단축됩니다.
  • 기동 TORQUE가 INDUCTION MOTOR에 비해 높습니다.
  • 삼상 380V~440V 모터에서는 인버터를 사용할 수 없습니다. 권선의 절연이 열화되어 모터가 파손될 수 있습니다.
  • For motor with straight shaft, please write S in place of PF in Motor Type. 
  • Motor Type in green screen represents the motors with TP(Thermal Protect) according to 
  • UL or CE regulation
  • Reversing direction without stopping completely may result in damage to the motor and reduce the life of the motor due to excessive inertia.
  • The starting torque is higher than that of the INDUCTION MOTOR.
  • ※ The inverter is not available on three phase 380V~440V motors. 
  • Insulation of windings may deteriorate and damage the motor

■ RATED TORQUE OF GEARED MOTOR

(unit : kg·cm)

Speed of Geared Motor rpm 500 300 200 120 100 60 50 30 20 15 10
Gear Ratio 50Hz 3 5 7.5 12.5 15 25 30 50 75 100 150
60Hz 3.6 6 9 15 18 30 36 60 90 120 180
IHK8PF25 + 8H□FM 4.6 7.6 11 19 23 34 41 61 92 100 100
IHK8PF25 + 8H□FB 4.4 7.4 11 18 22 33 40 60 90 100 100
  • 그린상자표시한 감속비의 감속기는 출력축의 회전방향이 모터축의 회전방향과 반대로 됩니다.
  • 감속모터의 회전수(Speed of Geared Motor)는 모터의 회전수 (50Hz에서 1500rpm, 60Hz에서 1800rpm)를 기준하여 산출하였습니다.
    실사용시의 회전수는 부하의 크기에 따라 위의 표보다 2~15% 작게 됩니다.
  • 하얀상자부에는 감속비를 지정하여 주십시오. 감속기는 별도로 판매 됩니다.
  • The rotation of geared motor in green screen is reverse of motor rotation. 
  • Speed of Geared Motor is based on motor synchronous speed. In normal operation, the speed will 
  • be 2 to 15 percent lower than above figure. 
  • When ordering gear head, please fill blank □ with gear ratio

■ MOTOR(STRAIGHT SHAFT)IHK8S25WT 1.7kg

■ GEARED MOTORIHK8PF25 + 8H□ FM(8H□ FB)WT 1.7+0.5/0.6kg

■ BOLT SIZE

No L(mm) GEAR RATIO BOLT SIZE
01 32 1/3 ~ 1/20 M5×60
02 42 1/25 ~ 1/200 M5×70

■ KEY SPEC

■ WIRING DIAGRAM

  • 모터의 회전방향은 샤프트 끝쪽에서 볼때의 회전방향입니다.
  • 모터의 회전방향 전환은 모터가 완전히 정지한 후 실시하여 주십시오.
  • The direction of rotation is seen from the end of motor shaft.
  • Change the rotation direction of the motor only after the motor stops completely.